Rheem Thermal, Air To Water Heat Pump Hydronic Heaters 
Click To Enlarge

 

Rheem Thermal, Air To Water Heat Pump Hydronic Heaters

RH

 

* FROM RHEEM THERMAL WE NOW HAVE THE NEW AUSTRALIAN MADE "Premium Rheem Thermal Range" OF HEAT PUMPS FOR HYDRONIC HEATING THAT HAVE UP TO 50% CHEAPER RUNNING COSTS THAN NATURAL GAS  SYSTEMS & UP TO 80% CHEAPER RUNNING COSTS THAN LPG HEATERS. These Heat Pumps can be supplied as dedicated Hydronic Heating Solutions OR as COMBI systems that provide a combination of HYDRONIC, DOMESTIC HOT WATER, SWIMMING POOL HEATING and can ALSO be supported by a WOOD FIRE with a WET BACK and SOLAR HOT WATER and SOLAR ELECTRIC PANELS. These are the BEST VALUE FOR MONEY HEAT PUMP on the AUSTRALIAN MARKET TODAY. Do not compromise for cheap imports with poor components and no service support.

 AA  

 

A clean and silent approach to space heating
Hydronic heating provides a luxurious form of space heating for homes and commercial buildings, with heated water circulated either via underfloor loops or radiators. Hydronic heating creates constant temperature distribution and its radiant heating warms objects rather than air by natural convection, giving great heating efficiency and comfort.
Capability
The Accent hydronic heat pump uses the best refrigerants and is available in both air-to-water and ground-sourced/water-to-water design. Air-to water type is suitable for an operating range between 0°C to 40°C ambient. The use of water-to-water design (with the water source may be a dam, river or canal) or ground-coupled type (where the fluid is typically a water/glycol mix which is circulated in a closed ground loop) allows the use of heat pumps in cold climate zones where sub-zero ambient temperatures would otherwise preclude this technology. For a water-sourced unit, the minimum entering water temperature to the heat pump’s secondary side would be 12°C, with the leaving water at 7°C. These parameters lower to 0°C/-5°C for water circulating in a closed ground-loop given that the risk of freezing is eliminated by the use of glycol. These units are capable of heating
water up to 61°C but are also manufactured as reverse cycle to provide a potential for space heating and cooling.
Efficiency
The efficiency of these units in hot water production is broadly in the range of 2.5 to 5.0, with this figure varying depending on the temperature requirements of the application as well as the temperature of the heat source.
Range
Our residential range focuses on Heat Pumps for home space heating with single phase options to a nominal heating capacity of 10kW to 24kW and three phase options from 24kW to 66kW. The commercial range includes units up to 339kW. Technical data for a cross-section of the range is given on the PDF document you can download below just above the pricing. Contact would be welcomed on other capacity and design configuration options.
Breadth of use
The standard function of these units is to provide comfort space heating and cooling but the robustness and versatility of the Accent design has seen use in a wide variety of applications, particularly in primary industries (such as piggeries and poultry sheds) and agriculture (greenhouse heating).
Extra Features
Heat exchangers can be stainless steel plate or copper shell-in-tube. Copper shellin-tube may be upgraded to cupro-nickel, either side, single-wall or with optional vented design. Flow switch protection. Multiple safeties including low temperature freeze protection on the chilled water side. Full commercial construction with marine grade aluminium case. Digital controls and upgradable to Rheem IQ® including BMS

 ET

RHEEM PREMIUM THERMAL RTHP SERIES

• Full commercial construction including marine grade aluminum case and anti-corrosion

  treatment of the evaporator

• 10.0kw to 66.0kW output

• Market leading level of efficiency

• Demonstrably lower running cost than competitor offering due to higher efficiency

• Best suited to Australian conditions with enhanced evaporator and heat exchanger capacity

• Suited to cool climate operation

• Compressor housed in separate internal cabinet minimizing noise.

• Over temperature control

• HP/LP pressure control and flow switch

• Marine Grade Aluminum Case, with the option of colour matching

• Australian-made

• Full manufacturer’s warranty and factory/service support nationally

• Faster temperature rise relative to competitor models based on higher heat transfer efficiency

rk

 SIDE OR TOP DISCHARGE

SIDE-AIR-DISCHARGE CONDENSING UNITS

 

PHP

 

Air To Hot Water condensers all discharge cold air. Most early condensers discharged the air out the side and were called side discharge.  The advantage of this equipment is that the fan and motor are under the top panel, therefore protected from heavy weather, leaves etc, and the discharge air and sound is blown in one direction. This is also ok for installations under decks etc.

TOP-AIR-DISCHARGE CONDENSERS

 

AA

 

The modern trend in residential equipment is for the condenser to be a top-discharge type.  In this type of unit, the cold air and noise are discharged from the top of the unit into the air.  This is advantageous as far as air and noise are concerned, but the fan and motor are on top of the equipment, and rain, snow, and leaves can fall directly into the unit, so the fan motor should be protected with a rain shield.

 

* Heat Pump Systems perform differently depending on Geographic Location, contact us today so we can complete an assessment on your project, these costs will reduce further if you install a Solar Power System. Click on the links below for more information.


Your Hydronic Heating System Design



More Info

Calpeda NC3 Cast Hydronic Circulating Pumps

from $60.50

More Info

Stieble Eltron Hydronic / DHW Storage & Buffer Tanks



More Info

Wilson Hydralux Thermal Storage & Heat Exchange Buffer Tanks

from $2,850.00

More Info

 

 

 

 

 

 

 

 

 

 

 

See Latest Brochure PDF Below

PDF: download
Price (each):
RTHW010-1, Single Phase, R407c, 10.3 kW, single wall/thermo control/side discharge.  $4,812.50 
RTHW010-1, Single Phase, R407c, 10.3 kW, single wall/thermo control/top discharge.  $4,812.50 
RTHW015-1, Single Phase, R407c, 15.0 kW, single wall/thermo control/side discharge.  $6,256.80 
RTHW015-1, Single Phase, R407c, 15.0 kW, single wall/thermo control/top discharge.  $6,256.80 
RTHW020-1, Single Phase, R407c, 19.0 kW, single wall/thermo control/side discharge.  $8,085.00 
RTHW020-1, Single Phase, R407c, 19.0 kW, single wall/thermo control/top discharge.  $8,085.00 
RTHW020-3, Three Phase, R407c, 19.1 kW, single wall/thermo control/side discharge.  $8,085.00 
RTHW020-3, Three Phase, R407c, 19.1 kW, single wall/thermo control/top discharge.  $8,085.00 
RTHW025-1, Single Phase, R407c, 25.3 kW, single wall/thermo control/side discharge.  $8,470.00 
RTHW025-1, Single Phase, R407c, 25.3 kW, single wall/thermo control/top discharge.  $8,470.00 
RTHW025-3, Three Phase, R407c, 25.4 kW, single wall/thermo control/side discharge.  $8,470.00 
RTHW025-3, Three Phase, R407c, 25.4 kW, single wall/thermo control/top discharge.  $8,470.00 
RTHWO26-1,Single Phase Low Noise, R407c, 26.22 kW,single wall/thermo probe control/ top discharge.  $9,091.50 
RTHWO26-3,Three Phase Low Noise, R407c, 26.22 kW,single wall/thermo probe control/ top discharge.  $9,164.00 
RTHW040-3, Three Phase, R407c, 39.4 kW, single wall/thermo control/side discharge.  $14,025.00 
RTHW040-3, Three Phase, R407c, 39.4 kW, single wall/thermo control/top discharge.  $14,025.00 
RTHW050-3, Three Phase, R407c, 52.6 kW, single wall/thermo control/side discharge.  $17,952.00 
RTHW050-3, Three Phase, R407c, 52.6 kW, single wall/thermo control/top discharge.  $17,952.00 
RTHW065-3, Three Phase, R407c, 66.0 kW, single wall/thermo control/side discharge.  $19,822.00 
RTHW065-3, Three Phase, R407c, 66.0 kW, single wall/thermo control/top discharge.  $19,822.00 
HW22-3, Watermark, Three Phase, R134a, 20.4kW. single wall/thermo control/side.  $10,528.00 
HW22-3, Watermark, Three Phase, R134a, 20.4kW. single wall/thermo control/top.  $10,528.00 

Quantity   for 
Rheem Heat Pumps